Mipa Plastic Primer Spray Adhesion Promoter for Plastics transparent silver 400 ml
€12.95
- Adhesion promoter for ABS, PP/EPDM, PC, PA, PUR, PVC and other automotive plastics
- At 20 °C dust-dry after 5 to 10 minutes, recoatable after 10 minutes
- Transparent silver: areas already painted remain visible
- Highly elastic, moves with the flexing of soft attachment parts
- 14 days right of withdrawal
- Expert advice: 02831 9167703 Mon–Thu 9–16, Fri 9–12 (CET)
- Specialist dealer in Kevelaer, Lower Rhine
Description
Mipa Plastic Primer Spray is a solvent-based 1K adhesion promoter for the subsequent painting of plastic parts. According to the manufacturer, it adheres to most plastics used on vehicles, including ABS, PP/EPDM, PC, PA, POM, PVC and both hard and soft PUR. The 400 ml spray can is intended for painters, body shops and DIY enthusiasts who want to make bumpers, spoilers or mirror housings paintable without a spray gun.
Advantages at a glance
- Wide range of plastics: approved for ABS, EP laminate, PA, PBTP, PC, POM, PP/EPDM, PPO, hard PUR, soft PUR and PVC.
- Fast working: at 20 °C dust-dry after 5 to 10 minutes, recoatable after about 10 minutes.
- Thin film: 2 to 3 spray passes give only 3 to 5 micrometres and do not build up on fits.
- Transparent silver: areas that are already painted remain visible during application.
- Highly elastic: the film moves with the flexing of soft attachment parts.
Areas of application
- Exterior mirror housings, spoilers and bumpers before the topcoat
- Attachment parts made of ABS, PP/EPDM and PUR on cars and two-wheelers
- Plastic parts made of PC, PA, PBTP, POM, PPO and PVC
- EP laminate and glass-fibre reinforced components
- Furniture and housings made of hard plastic
Limits & notes
The primer is an adhesion promoter and not a final coat: it must be overpainted and on its own offers no protection against the weather. It must not be overworked with polyester materials. Release agent residues from plastic manufacturing must be removed completely, otherwise the coating will not adhere. Mipa recommends checking adhesion beforehand on an original part.
Hazard information: Danger. Extremely flammable aerosol. Pressurised container: May burst if heated. Causes skin irritation. Causes serious eye irritation. May cause drowsiness or dizziness. Harmful to aquatic life with long lasting effects. Safety data sheet available from the manufacturer.
Processing & tips
Temper the part for 60 minutes at 60 °C, degrease with plastic cleaner or silicone remover, sand thoroughly with a soft pad to a super-fine finish and clean again, then let it dry completely. The water wetting test shows whether the pre-treatment is sufficient: if the water beads off strongly, repeat the procedure. Shake the can for 1 to 2 minutes, test-spray, then apply from 20 to 30 centimetres in 2 to 3 thin spray passes, with a flash-off time of 2 to 3 minutes between passes. Solvent-based and flammable: use only with good ventilation and away from ignition sources; wear safety goggles and solvent-resistant nitrile gloves. When spraying indoors, also wear respiratory protection with an A2 gas filter. Processing temperature from plus 10 °C at no more than 80 percent relative humidity. After use, turn the can upside down and spray out the valve. Stored cool, dry and tightly closed, the product has a shelf life of 2 years.
Technical data
| Base: | Solvent-based |
|---|---|
| Colour: | silver |
| Content: | 400 ml |
| Material: | Synthetic resin |
| Pack size: | 400 ml spray can |
| Technical data | |
|---|---|
| Dry film thickness: | 3-5 µm with 2-3 spray passes |
| Density: | 0.755 g/cm³ at 20 °C |
| VOC content: | max. 757 g/l (limit category B/e 840 g/l) |
| Shelf life: | 2 years, cool and dry, tightly closed |
| Application | |
| Pre-treatment: | 60 min at 60 °C tempering, degrease, sand superfine with a soft pad, clean again |
| Spraying: | 2-3 thin spray passes, spray distance 20-30 cm, flash-off time 2-3 min |
| Drying at 20 °C: | dust-dry 5-10 min, recoatable after approx. 10 min |
| Application conditions: | from +10 °C, up to 80% relative humidity, with supply and extract air |
| Use | |
| Suitable plastics: | ABS, EP laminate, PA, PBTP, PC, POM, PP/EPDM, PPO, hard PUR, soft PUR, PVC |
| Not suitable: | Overworking with polyester materials |
| What's included | |
| Supplied as: | 400 ml aerosol can |
Frequently asked questions
Which plastics does the Mipa Plastic Primer adhere to?
According to the technical information sheet: ABS, EP laminate, PA, PBTP, PC, POM, PP/EPDM, PPO, hard and soft PUR, and PVC.
How long must the primer flash off before painting?
At 20 °C it is dust-dry after 5 to 10 minutes and recoatable after about 10 minutes.
Do I need to pre-treat the plastic part?
Yes: temper for 60 minutes at 60 °C, degrease, sand superfine with a soft pad and clean again. Release agent residues must be removed completely.
How do I know whether the pre-treatment is sufficient?
By the water wetting test: if the water beads off strongly, the part is not yet sufficiently prepared and the pre-treatment is repeated.
Does the primer remain visible on the component?
It is transparent silver, so areas that are already painted remain recognisable. It is overpainted afterwards and is not a final coat.
Manufacturer information
Manufacturer information pursuant to Art. 19 EU GPSR
Postal address
MIPA SE
Am Oberen Moos 1
84051 Essenbach
Germany
Electronic address mipa@mipa-paints.com
Information as of: 2026-11-09
Reviews
All reviews come from buyers. Reviews can only be submitted via the personal, signed link we send to the order's e-mail address after delivery; the link is bound to the order and the purchased item, there is no form without a purchase. We check every review before publication and publish positive and negative reviews alike. Reviews from our former shop baustoffhandel-nrw.de were migrated; there, too, only customers who had bought the item could review it.
For your project