Ottoseal A210 painter's acrylic white 310 ml cartridge
€2.95
- Low in odour, even in an occupied room
- A later coat of paint is compatible with the joint
- For connection joints in interior fit-out
- Survives transport and storage in light frost
- 14 days right of withdrawal
- Expert advice: 02831 9167703 Mon–Thu 9–16, Fri 9–12 (CET)
- Specialist dealer in Kevelaer, Lower Rhine
Description
- 1K acrylate sealant
- Permissible total deformation 10%
- Low odour
- Paint-compatible according to DIN 52452
- Can be stored and transported for up to 48 hours at a maximum of -10 °C
Areas of application:
Primarily suitable for interior fit-out
Expansion joints and connection joints with only low stress, e.g. between wooden window or door frames and masonry, plaster or concrete
Joints and connections on concrete, aerated concrete, plaster, masonry, wood, plasterboard, fibre cement, roller shutter boxes, window sills etc.
Special notes:
Before using the adhesive / sealant, the user must ensure that the building materials in the contact area (solid, liquid and gaseous) are compatible with the adhesive / sealant and do not damage or alter it (e.g. discolour it). For building materials that are subsequently processed in the area of the adhesive / sealant, the user must clarify beforehand that their ingredients or emissions cannot impair or alter the adhesive / sealant (e.g. discolouration). If necessary, the user must consult the respective manufacturer of the building materials. At normal temperature (23 °C / 50 % RH) the sealant forms a firm surface skin after approx. 2 hrs. Until then, rain or other exposure to water on the fresh sealant must be avoided at all costs. Lower temperatures and / or high humidity can considerably reduce the drying speed of the sealant. Do not apply at temperatures below +5 °C. During curing/drying the sealant changes colour. The final shade is reached after complete curing. Compatibility with water-based paints is given in most cases. Because of the large number of paint systems available on the market, however, we recommend checking the compatibility of sealant and paint or consulting our application technology department. According to the relevant standards, elastic joint sealants should in principle not be painted over the full surface, since, under stress and movement, cracks can appear in the paint coatings, which unlike the sealant are not elastic. Where the sealant is painted over in joints with little movement, a drying time of at least 1 week must be observed. Avoid contact with materials containing bitumen or releasing plasticisers, e.g. butyl, EPDM, neoprene, insulating and black coatings. After curing, the product is completely odourless, physiologically harmless and inert.
Pre-treatment:
The bonding surfaces must be clean, free of dust and grease and sound. The bonding surfaces must be cleaned and any contamination, such as release agents, preservatives, grease, oil, dust, water, old adhesives/sealants and other substances that impair adhesion, must be removed. Cleaning non-porous substrates: clean with OTTO Cleaner T (flash-off time approx. 1 minute) and a clean, lint-free cloth. Cleaning porous substrates: clean surfaces of loose particles mechanically, e.g. with a steel brush or a grinding disc. Absorbent mineral bonding surfaces should be dampened with water to improve adhesion. The following are also available to improve adhesion: on absorbent substrates - mixture of acrylic sealant/water 1:2 - on absorbent and non-absorbent substrates: primer
Application notes:
Apply the sealant evenly with a manual caulking gun, compressed-air gun or cordless gun and press the surface down with a dampened tool before a skin begins to form. Remove contamination with water while it is fresh. Because of the many possible influences during processing and application, the applicator must always carry out a trial application. The specific use-by date can be found printed on the container and must be observed. We recommend storing the adhesives / sealants in the unopened original containers dry (< 60 % RH) in a temperature range of + 15° C to + 25° C. If the products are stored and/or transported for longer periods (several weeks) at higher temperature/humidity, a reduction in shelf life or a change in material properties cannot be ruled out.
Supplied as:
310 ml cartridge
Colour:
white
Technical data
| Material: | Polyacrylate |
|---|
| Technical data | |
|---|---|
| Product type: | Painter's acrylic |
| Product group: | Acrylic sealant |
| Standards | |
| Standard: | DIN 52452 |
| Use | |
| Merchandise group: | Sealants |
| What's included | |
| Supplied as: | 310 ml cartridge |
Data sheets
Data sheets and documents
All documents come unchanged from the manufacturer.
Manufacturer information
Manufacturer information pursuant to Art. 19 EU GPSR
Postal address
Hermann Otto GmbH
Krankenhausstr. 14
83413 Fridolfing
Germany
Electronic address info@otto-chemie.de
Information as of: 2026-09-17
Reviews
All reviews come from buyers. Reviews can only be submitted via the personal, signed link we send to the order's e-mail address after delivery; the link is bound to the order and the purchased item, there is no form without a purchase. We check every review before publication and publish positive and negative reviews alike. Reviews from our former shop baustoffhandel-nrw.de were migrated; there, too, only customers who had bought the item could review it.
For your project
These products go with it
Customers also bought
Content: 0,2 Kilogram (€33.50 / 1 Kilogram)
Content: 0,31 Litre (€26.74 / 1 Litre)
Content: 0,3 Litre (€29.83 / 1 Litre)
Content: 0,31 Litre (€28.35 / 1 Litre)
Content: 0,31 Litre (€21.90 / 1 Litre)
Content: 0,4 Litre (€24.47 / 1 Litre)
from 12 pcs. €9.50/pc. (€23.75 / 1 Litre)