Skip to main content Skip to search Skip to main navigation

DENSO TOK-Band SK self-adhesive bitumen joint tape ZTV Fug-StB 15

Description

DENSO TOK-Band SK is a self-adhesive bitumen joint tape made from polymer-modified road bitumen, for sealing joints and seams in asphalt road construction. It was the world's first self-adhesive bitumen joint tape and is laid cold, without a gas burner and without primer.

Benefits at a glance

  • Fitted on one side with a homogeneous adhesive layer over the full surface, so it is fixed in seconds to the cold joint face
  • No primer needed as long as the face has been properly cleaned and is dust-free and dry
  • No gas burner and no open flame on site
  • Meets all requirements of ZTV Fug-StB 15, test certificates to TL/TP Fug-StB are available
  • Softening point above 100 degrees Celsius, so it stays stable even when the mix is laid hot

Areas of application

  • Joints and seams in asphalt and concrete surface courses
  • Connections of asphalt to fixtures such as manhole covers, road boxes and channels
  • Longitudinal and transverse seams when laying rolled asphalt, stone mastic asphalt and mastic asphalt
  • Service trenches and openings in the existing road structure

Limits & notes

Under ZTV Fug-StB, bitumen joint tapes may only be installed in dry weather and with a surface temperature of the asphalt of at least +5 degrees Celsius. Between 0 and +5 degrees Celsius, additional measures are required, such as preheating the faces. For installation at permanently lower temperatures, TOK-Band SK N2 is the right choice. The minimum tape width is 10 millimetres. Rust, loose particles and moisture on the abutting face prevent adhesion.

Application & tips

Lay out the tape with the smooth adhesive layer facing up against the prepared face and remove the release paper only immediately before laying. Then press the adhesive layer firmly against the abutting face by hand or with an auxiliary tool. The slightly wavy side stays exposed; the hot mix is later built up against it. On rolled asphalt surface courses, lay with a 5 millimetre overhang so that the so-called rivet head forms during rolling; on mastic asphalt surfaces, install flush. On dirty or difficult faces, the TOK-SK Primer improves adhesion to the face; its flash-off time in summer is 3 to 5 minutes, depending on the weather. Store rolls dry, without load and frost-free, ideally at 15 to 20 degrees Celsius.

Technical data

Area of use: Exterior
Content: 900 m
Material: Bitumen
Pack size: 900 m pallet
Version
Size: 40 x 10 mm
Technical data
Base: Polymer-modified road bitumen
Softening point (ring and ball): above +100 °C (requirement above +90 °C)
Cone penetration: 20 to 50 (0.1 mm)
Elastic recovery: 10 to 30 %
Cold bending behaviour: less than or equal to ±0 °C
Elongation and adhesion: at least 10 % / at most 1.0 N/mm²
Standards: ZTV Fug-StB 15, tested to TL/TP Fug-StB
Application
Application temperature: +5 °C to +50 °C, asphalt surface at least +5 °C
Pre-coat: not required, TOK-SK Primer optional
Storage: dry, without load, frost-free, ideally 15 to 20 °C, shelf life at least 2 years
Use
Tape overhang: 5 mm for rolled asphalt, flush for mastic asphalt
What's included
Supplied as: 900 m pallet with 30 cartons of 30 m each

Frequently asked questions

Do I need a primer for TOK-Band SK?

No. On a properly cleaned, dust-free and dry face the tape adheres without primer. TOK-SK Primer only improves adhesion on difficult or dirty substrates.

From what temperature may TOK-Band SK be installed?

The application temperature is between +5 and +50 degrees Celsius, and the asphalt surface must be at least +5 degrees. Between 0 and +5 degrees, additional measures are needed.

How many metres does a pallet contain?

A Euro pallet always holds 30 cartons. Depending on the profile, this gives 900 to 1500 metres.

How long can TOK-Band SK be stored?

Stored dry, without load and frost-free, for at least two years from the date of manufacture in the unopened original packaging.

How much overhang does the tape need when installed?

On rolled asphalt surface courses, a 5 millimetre overhang, so that the rivet head forms during rolling. In mastic asphalt, it is installed flush.

Manufacturer information

Manufacturer information pursuant to Art. 19 EU GPSR

Postal address DENSO GmbH
Felderstraße 24
51371 Leverkusen
Germany

Electronic address info@denso-group.com

All products by DENSO

Information as of: 2026-11-08

Reviews

0 of 0 reviews

Average rating of 0 out of 5 stars

All reviews come from buyers. Reviews can only be submitted via the personal, signed link we send to the order's e-mail address after delivery; the link is bound to the order and the purchased item, there is no form without a purchase. We check every review before publication and publish positive and negative reviews alike. Reviews from our former shop baustoffhandel-nrw.de were migrated; there, too, only customers who had bought the item could review it.